加拿大Solinst温度液位电导率TLC仪表分析仪(107)

品牌：Solinst

产地：加拿大

型号：107

 

Solinst TLC 107仪表是分析井和开放水域的电导率和温度的理想选择。

107 型 TLC 仪表非常适合分析井和开放水域的电导率和温度、盐水侵入 研究以及污染水平的一般指示。直径为 3/4" (19 mm) 的探头连接在 Solinst PVDF 扁平胶带上；每 1/100 英尺或每毫米进行一次精确的激光标记。长度可达 1000 英尺或 300 m，安装在 Solinst 卷轴上。

 

电导率范围为 0-80,000 µS/cm。电导率和温度测量值显示在卷轴正面的旋转 LCD 屏幕上。电导率精度为读数的 5% 或 100 μS（以较大者为准）。当探头的零点进入水中时，指示灯和蜂鸣器会短暂激活。从磁带上读取到水的深度和显示读数的深度。9V 碱性电池装在一个易于取用的电池抽屉中，可提供长达 90 小时的使用时间。

 

TLC 仪表非常适合分析井和开放水域的电导率和温度。它在方便的 LCD 显示屏上显示电导率和温度的准确测量值。

电导率测量值的读数范围为 0-80,000 μS/cm，读数精度为读数的 5% 或 100 μS（以较大者为准）。

水位和探头深度测量值从 Solinst 耐用的 PVDF 扁平胶带上读取，该胶带每 1/100 英尺或每毫米进行一次精确的激光标记。现在可提供长达 1000 英尺 (300 m) 的胶带长度。

对于自动水位、温度和电导率数据记录，Solinst 还提供 Levelogger 5 LTC。（参见3001 型 Levelogger 5 LTC 数据表）。

 

磁带长度可达 1000 英尺 (300 m)

坚固的 Solinst 卷盘和精确的 PVDF 激光打标胶带

探头直径 3/4" (19 mm)

标准 9V 碱性电池可提供 90 小时。使用

8分钟后自动关闭

 

无论温度如何，高品质 PVDF 扁平胶带都能顺畅地卷起、保持柔韧性并笔直悬挂在井中。扁平胶带安装在一个坚固、平衡良好的 Solinst 卷轴上，并带有一个方便的电池抽屉，用于放置 9 伏碱性电池。每 1/100 英尺或毫米的永久激光标记允许准确读数。

标准不锈钢导体和镀铜不锈钢导体抗腐蚀、提供强度且无拉伸。它们使胶带易于维修和拼接。狗骨设计减少了对潮湿表面的粘附。

LM2：每个 1/100 ft、1/10 ft 和 ft

LM3：每个 mm、cm 和 m

 

长度：

100 英尺、200 英尺、300 英尺、500 英尺、750 英尺、1000 英尺

（30 m、60 m、100 m、150 m、250 m、300 m）

 

TLC Meter使用带有铂电极的“智能”电导率传感器来测量电导率。电导率与相关的温度测量值一起显示在屏幕上。“智能探头”显示已标准化为 25°C 的电导率，即比电导率（显示为 EC）。电导温度系数为 2.0%/°C。

 

校准很简单，使用 1413 μS、5000 μS、12,880 μS 和/或 80,000 μS 溶液进行 1、2、3 或 4 点手动电导率校准。

 

分析井和开放水域的电导率和温度

盐度研究

盐水入侵调查

测试道路盐对水质的损害

示踪剂测试

化学污染水平的一般指示

水质变化预警：

垃圾填埋场

工业用地

 

当探头的零点进入水中时，电路完成，短暂激活蜂鸣器并使屏幕消隐约 1 秒钟。然后从磁带上读取到水的深度。当TLC 仪表从水中取出时，短暂的嗡嗡声会发出警告，表明探头现在已出水。

导带器/基准允许在导带器上的标记位置读取深度测量值，以便在剖析井时提供可靠、可重复、准确的深度测量。导带器可保护胶带免受井套管粗糙边缘的损坏。

 

TLC 仪表的工作温度范围为 -15°C 至 +50°C（23°F 至 122°F）。您可以选择在 LCD 屏幕上以°C 或°F 显示读数。精度为摄氏 +/- 0.2°C，或华氏 +/- 0.4°F。“智能”TLC 探头会自动调整测得的电导率值以显示为比电导率。这提供了标准化的可重复可比测量。

当探头打开时，LCD 屏幕显示电导率和温度。

中文内容来自机器翻译，内容仅供参考，实际内容可参考原厂介绍或以合同为准。

英文原文：

 

The Model 107 TLC Meter is ideal for profiling conductivity and temperature in wells and open water, for salt-water intrusion studies, and a general indication of contamination levels. The 3/4" (19 mm) diameter probe is attached to Solinst PVDF flat tape; accurately laser marked every 1/100 ft or each millimeter. Lengths up to 1000 ft or 300 m, mounted on a Solinst reel.

 

The conductivity range is from 0-80,000 µS/cm. Conductivity and temperature measurements are displayed on a rotating LCD screen on the face of the reel. Conductivity accuracy is 5% of reading or 100 μS (which ever is greater). A light and buzzer are briefly activated when the zero point of the probe enters water. The depth to water and depth of displayed readings are read off the tape. The 9V alkaline battery is housed in an easy-access battery drawer and provides up to 90 hours of use.

 

Model 107 TLC Meter (Temperature, Level, Conductivity)：

The TLC Meter is ideal for profiling conductivity and temperature in wells and open water. It displays accurate measurements of conductivity and temperature on a convenient LCD display.

 

Conductivity measurements are read from 0-80,000 μS/cm with readings giving accuracy of 5% of reading or 100 μS (which ever is greater).

 

Water level and probe depth measurements are read off the Solinst durable PVDF flat tape, which is accurately laser marked every 1/100 ft or each millimeter. Tape lengths are now available up to 1000 ft (300 m).

 

For automated water level, temperature, and conductivity datalogging, Solinst also offers the Levelogger 5 LTC. (See the Model 3001 Levelogger 5 LTC Data Sheet).

 

Conductivity Made Easy：

Tape lengths to 1000 ft (300 m)

Rugged Solinst reel and accurate PVDF laser marked tape

Probe diameter 3/4" (19 mm)

Standard 9V alkaline battery gives 90 hrs. of use

Auto-Off after 8 minutes

 

Rugged PVDF Flat Tape：

The high quality PVDF flat tape reels smoothly, remains flexible and hangs straight in the well, irrespective of temperature. The flat tape is mounted on a sturdy, well-balanced Solinst reel, with a convenient battery drawer for the 9 Volt alkaline battery. Permanent laser markings each 1/100 ft or millimeter allow accurate readings.

 

Standard stainless steel conductors and copper coated stainless steel conductors resist corrosion, provide strength and are non-stretch. They make the tape easy to repair and splice. The dog-bone design reduces adherence to wet surfaces.

 

LM2: Each 1/100 ft, 1/10 ft and ft

LM3: Each mm, cm and m

 

Lengths:

100 ft, 200 ft, 300 ft, 500 ft, 750 ft, 1000 ft

(30 m, 60 m, 100 m, 150 m, 250 m, 300 m)

 

Water Conductivity Measurements：

The TLC Meter uses a 'smart' conductivity sensor with platinum electrodes to measure conductivity. The conductivity is displayed on the screen along with the associated temperature measurement. The 'smart probe' displays conductivity that has been standardized to 25°C, i.e. Specific Conductance (displayed as EC). The conductance temperature coefficient is 2.0% per °C.

 

Calibration is simple, using 1413 μS, 5000 μS, 12,880 μS, and/or 80,000 μS solutions for 1, 2, 3, or 4 point manual conductivity calibrations.

 

Applications：

Profiling conductivity and temperature in wells and open water

Salinity studies

Saltwater intrusion investigations

Testing for water quality impairments from road salt

Tracer tests

General indication of chemical contamination level

Early warning of changes in water quality at:

Landfills

Industrial Sites

 

Water Level and Depth Measurements：

When the zero point of the probe enters water, an electric circuit is completed, briefly activating a buzzer and blanking out the screen for about 1 second. The depth to water is then read off the tape. When the TLC Meter is withdrawn from the water, a short buzz gives a warning that the probe is now out of water.

 

A Tape Guide/Datum allows the depth measurement to be read at the marked position on the Tape Guide, to give reliable, repeatable, accurate depth measurements when profiling a well. The Tape Guide protects the tape from damage on rough edges of well casing.

 

Water Temperature Measurements：

The TLC Meter operates in a range from -15°C to +50°C (23°F to 122°F). You may choose to have the readings displayed on the LCD screen in °C or °F. Accuracy is +/- 0.2°C in Celsius, or +/- 0.4°F in Fahrenheit. The 'smart' TLC probe automatically adjusts the measured conductivity values to display as specific conductance. This provides standardized repeatably comparable measurements.

 

When the probe is turned on, the LCD screen displays both conductivity and temperature.